English Layout Square

Published on by Mike  (2 Comments)

squares_cleaned_upAs I have mentioned in other posts, I am pretty active in the chat room that is associated to The Wood Whisperer.  We will on occasion have challenge and trade projects, where we build something that is designed to push our skills, and then send it to another member.  This time we chose to do a woodworking hand tool.  Something we did a little different with this one, is we ran it similar to a secret Santa, where we found out who we would be sending our tool to before we got started. However, we did not know who we would be receiving from.

For my tool, I built an English Layout Square.  Actually, I built two of them.  Since I knew this project would really stretch my skills, I wanted one to practice each step, before doing the step on the piece I sent out.  While the practice square has a couple obvious mistakes, it turned out well.   As soon as I find a spot for it, the practice square will be hung on the wall, ready for use.

The wood I used is cherry.  After milling the cherry down to 1/2″ thickness, I sized up the two main arms of the square.  The joint to bring the two arms together is a bridal joint.  The tenon for this bridal joint was thin, coming in about 1/8″.  I made this tenon using a shop made tenon jig on the table saw.  Using the same jig, I adjust the distance of the tenon jig from the blade to get the work piece as centered as possible, to allow the table saw to hog out the center.

arm_detailAfter getting the bridal joint done, the traditional English Layout Square has a lot of ornamental detail to it.  I roughed out most of this detail on the band saw, and then where I could, used the oscillating spindle sander to clean up the detail.  The rest, I cleaned up by hand, using my rasp, chisels, and sand paper.

Once I got the detail work done, it was time for the first glue-up.  After several dry fits, I was able to get the bridal joint to fit together well.  The mistake I made was I let it be a little too tight.  The problem with that is the wood swelled a bit when I applied the glue.  I was able to get the pieces together, but it proved to be a challenge.   The other challenge to this glue-up is making sure I got the square as close to 90 degrees as possible.

cross_brace_fittedThe next step was working on the cross brace.  The joinery for that is two half lap joints.  I did this almost entirely with hand tools.  Once I establish the position of the cross brace, I stuck a line using a marking knife on the arms.  I used the marking gauge to set the distance down to so that I was removing just shy of 1/4″ of material.  Once I got all that indicated, I used chisels to cut small channels along the cut lines, where I then was able to follow those with my crosscut saw, and cut down 1/4″.  Using my chisel and mallet, I cleared out as much material as possible.  I then cleaned it up using my router plane.  Once that was done, I fitted the cross brace back into the square.  This allowed me to mark on the brace where I needed to cut.  I again, used chisels to cut a channel, and cut down a 1/4″ with the crosscut saw. Using a resaw cut, I cut away as much of the half lap as I could, and the finished the cut using a dovetail saw.  Finally I popped out the remaining piece with a chisel.  I cleaned up and fitted the brace using the router plane.

Once the half laps were fitted, I completed the ornamental work using the same methods I did with the arms.  Once I got it looking good, I glued the cross brace in place.

square_squareOnce the glue was dried, I started cleaning up all three joints.  This was mostly done with my smoothing plane and block plane.  I then sanded the faces of the square to 220.  Now came the square of the blade.  I used my framing square as a reference for getting the layout square.  After marking a line on the square as to where I needed to go down to, I used my smoothing plane to trim away some material to bring it closer to square.  Then using the jack plane, I established a straight edge.  I repeated this a few times till the square was, well, square.

square_completeThe finish was fairly simple.  I wiped on a coat of boiled linseed oil, and let it set for a week.  On a very sunny day, I set the square out in the sun to let the cherry darken a bit.  Once the oil had cured, I buffed it out using the Beall buffing system.

This turned out to be a very fun project for me, as well as a good challenge.  I accomplished making some joinery that I have never done before, as well as pushed my hand tool skills further along.

Lumber Rack

Published on by Mike  (Leave a comment)

in_progressOne of the big areas my shop has lacked is good lumber storage.   Most of the time when I buy wood, I buy just enough to accomplish the project, with maybe an extra board or two just to have on hand for when I need to remake a piece I screwed.  (That never happens right?!?)  In away this has been a benefit in my overall growth as a woodworker as it has forced me to try to recover from mistakes without making new parts.  Hopefully this will always be the mindset I work on at this point.  The drawback of buying wood this way is it is more expensive.  My local wood supplier often has good deals on wood, but in most cases to take advantage of the deal you have to buy 100 board feet as minimum.  I simply did not have the space for that much wood.  The small space I had stored my wood, only allowed for about 20-25 board feet, and was vertical storage.  While vertical storage isn’t necessarily a bad thing, for my situation, it was just propped up against the wall, and was prone to falling over.  Also, it was often in my way when trying to get to the my dust collector.  It was time to make some changes to the garage and build a lumber rack.

The first challenge I had, was where do I put it?  All my walls were full with either peg board or other items hanging on it.  And when I say peg board, it was full 8’x4′ sheets of peg board.  However, one sheet was over where we keep our trash cans, and some other storage, and as I was looking at it, I realized everything that was on it could either be put someplace else, or go in the trash.    This meant  I could free up a section of wall that was 8′.  PERFECT!  So I cleared out that area, and I pulled down the pegboard.  There were some other hooks and hangers on the wall that I also took down that freed up even more space.  After I got it all cleared out, I made some minor repairs to the wall, and I was ready to go.

completeThe construction really was pretty simple.   The design of the rack I took notes from various racks out on the Internet as well as studied the design from TheWoodWhisperer.com and came up with one for what I need.  The bones of the rack were constructed from construction grade 2x4s, and I used some inexpensive plywood from Menards.  Each bracket of the rack is a laminated 2×4 with an oversized plywood on either side.  These were constructed with glue and nails.   I decided to go with 3 rows of brackets.  Since the wall studs were 24″ on center, I needed to make 5 columns, so this would need 15 total brackets.  Once the brackets were complete, I could work on the vertical supports.  I drill counter bored holes for the lag bolts.  I then put up each vertical support so that it was supported on the garage floor, and the lagged bolted them into the wall studs.  I then used my laser level to mark out each row, and screwed in place each bracket.  Each bracket has 8 screws that go through the entire width, so it will be good solid.

The top row I discovered is actually above the track for the garage door.  I decided that this is fine, as I am not going to put a lot of weight up there, and use it mainly for storage for long items that I need out-of-the-way.  The bottom tow rows will be dedicated to lumber.

loaded_upThe only thing missing at that point was the wood!  My favorite go to hardwood supplier is Muterspaw Lumber, located in Xenia Ohio.  Check out his website at CRLumber.com as he also ships lumber all around the country.  The owner, Chad Muterspaw, had been running a special on cherry for a while that I had wanted to take advantage of, and I now have the room to store it.   That 100 board feet of cherry fit very well on the first row of my lumber rack, so I have plenty of room for future wood purchases!

Router Table – Wrap Up

Published on by Mike  (2 Comments)

router_table_completedWow!  This turned out to be the biggest and most complex project I have completed yet in my wood shop.  And I would do it again in a heart beat!  I looked back on my first post for the router table, where I had defined the goals I wanted to achieve for the new table.  I am happy to say I have achieved them all!  The router table truly is a joy to use!

A couple quick things I wanted to highlight that I didn’t cover in previous posts.  The first is the drawer pulls.  drawer_pullsI ended up turning all the pulls for the drawers.  Each drawer has two pulls on it, and there are 6 drawers.  If you ever want to good practice and replicating parts on a lathe, turn 12 pulls!  There was some variation between each one, but over all they were each a good match with the rest.  The other item I wanted to mention is the bit storage.  For now I kept it simple just by taking a length of plywood, drill a bunch of 1/2″ and 1/4″ holes, and screwed it to one of the vertical drawers.  With the setup I came up with for bit storage I will be able to change and rearrange it as my bit collection continues to evolve.

bit_storageA quick note about the vertical drawers.  I took a small risk and tried something different and unique with them.  As of this post, I have actually been using the table for a couple of months, and I can honestly say I love the configuration.  One drawer is designated for wrenches, collets, height adjuster, and various other components I use frequently.  The other is for bit storage.  Both provide very easy access to getting what I need, while keeping everything very organized.

Thank you all for following along!  On to the next project!

 

Router Table – The Fence and Dust Collection

Published on by Mike  (Leave a comment)



Trt_fencehe fence from the old table was another area of the router table that had some room for improvement.  Overall the new fence is mostly a bigger version of the old one, with a sliding split front that I can have an opening that is sized to the bit being used, with a length of t-track for attaching feather boards, stops, and a guard.  The big improvements I made are how the fence attaches and clamps down to the table, and the dust collection.  On the old table I routed a couple grooves that a couple of carriage bolts would travel in.  Those bolts went through a couple of holes the base of the fence with a couple of wing nuts to lock it in place.  This worked fine, but what I didn’t like about it is that I had to completely disassemble them to remove the fence from the table.  fence_clampI have observed several fence designs where the fence extends over the table on either side and then uses wood blocks to clamp the fence to the table.  While it was a bit of a trial and error process, this is the design I went with.   What I found is the clamp blocks work best when the wood clamp blocks slightly engage the bottom of the table.  The top of the block is tapered just a bit so that it will cause the block to pull up evenly to the bottom of the table, resulting in a very strong fit, as well as releasing cleanly.  fence_leverThe first iterations when I loosened the knob, the clamp blocks remained engaged.  Once I finally got the clamps working as needed I switched out the knobs with cam levers from Rockler, which work very well to quickly lock and unlock the fence.

dust_collection One of the top priorities for a new router table was dust collection.  The router table has always been a big source of shavings and dust.  The dust collection for the router table is done in two parts, divided between the space under the router table that contains the router and lift, and the fence.  To accomplish this, I got a 4″ Y fitting where one of the forks is reduced to 2.5″.  Using a scrap piece of hardwood, I marked the perimeter of the Y, that I then cut out the hole using the band saw and the oscillating spindle sander to get a good fit.  Since I kept the back of the router table removable, I marked approximately where I wanted the DC to go in, and took off the back.  I then used the piece I just made to mark precisely where the dust collection would go in.  I cut out the opening with a jig saw.  From there I double side taped the reference piece to the back, and used a flush trim bit on the router to get the opening properly sized and shaped.  On the inside portion I ran a chamfer around the perimeter of the hole as well, which should help the flow a bit.  While the back was off, I decided I didn’t want to glue the fitting to the back directly so that I could make tweaks as needed, so I lined up the scrap piece I had made to the hole and screwed it in place where I then glued the Y to it with Gorilla Glue.  The foaming did very well to close up any gaps.  dust_collection_insideWhile the glue dried, I turned my attention to the fence.  I bought a 2.5″ connector that would attach to a piece in the back of the fence.  I used the jig saw on a square piece to get the approximate hole I needed.  With the connector attached, I used the flush trim bit on the router table to get the hole sized perfectly.  I then made a couple triangular wedges that I attached to the back of the fence, and then attached the connector piece.  Once the glue dried on the Y, I cleaned up any excess foam and attached it to the back of the router table.  I then took the 2.5″ hose, pushed the fence as far forward as I would ever need it to determine the length, and cut the hose to length, a little longer than needed.  Using hose clamps I attached the hose to the fence and to the Y.  On the open end of the Y, and blast gate was attached, that was then tied into my dust collection system. With that, I made sure all the other blast gates, opened up the one on the router table, lined up the fence close to the bit, and power up the dust collector.  I could feel plenty of air moving through the table, so I made a few passes with a round over bit.  I am happy to say the dust collection works very well both on top of the table at the fence, and below the table!

I am going to have one more post on the router table, where I will cover the drawer pulls, finish, and some finishing touches.

Router Table – The Drawers & Door

Published on by Mike  (Leave a comment)

drawer_boxOne of my requirements for a new router table was a cabinet that had plenty of storage.  So  I designed it with 4 traditional drawers and 2 vertical drawers.  The traditional drawers are basic plywood boxes, with an applied hardwood front.  The boxes were assembled using rabbets and dados.  There is a groove in the bottom to accept a 1/4″ thick piece of plywood for the bottom.  The drawer boxes are sized so that they slide in and out of the cabinet easily.  The backs of the drawers are inset a couple inches so that they can slide out enough that I am able to get full access to the drawer contents, but it won’t fall out of the cabinet.

vertical_drawerThe vertical drawers are something unique I came up with, that will hopefully give me a greater amount of flexibility on my storage needs.  The concept is very similar to what I did for the hand tool cabinet.  The main panel is a 3/4″ thick piece of plywood attached to the sides of the cabinet with full extension drawer slides.  A front is attached with brackets and pocket screws.  The right vertical drawer I have a couple shallow boxes attached to it that stores everything I need for bit changes and adjustment.  This has proven to be very useful.   Currently the left vertical drawer is empty, but I plan to use this mainly for bit storage.

drawer_boxes_installedThe fronts of the drawers are made from ash.  The fronts for the bottom 3 drawers were made from one panel of wood so that I can get a good grain match.  I also attempted to make the 2 smaller drawers look like they are one piece, though it is two.  Attaching the drawer fronts turned out to be straight forward.  Since I am turning the pulls on the lathe, I figured I could use that to my advantage.  I measured out and predrilled screw holes with a fairly deep counter sink.  I then put screws in enough that I could push them against the draw box.  Once I was satisfied with the alignment I screwed the screws home.  I then put it four more screws from behind to get a solid fit.  For the space directly under the router table, the front was a piece of plywood which looked out of place next to all the ash.  So I made a false front in the same style of the drawers.

door_frame_rabbetThe door is similar to a frame and panel door, except that instead of a wood panel, it is using a plexiglass insert.  I didn’t want to run a groove all the way around, so I used the router tablento put mortise on each end of the 2 stiles. I did this on the router table with a 1/4″ bit.  Using a rabbet bit I made the tenons on the rails.  I then glued up the frame.  Using the same rabbet bit, I put a rabbet all the way around the back of the inside portion of the frame which is deep enough to accept the plexiglass and push pins to hold it in place.  After routing out the rabbet, I used a couple chisels to square the corners.  On the front, again inside the frame, I routed a round over.  Using my rasp and some sand paper I cleaned up the corners.  The plexiglass panel has holes drilled into it for back flow for the dust collection.

router_table_frontAll that is left is the pulls.  They aren’t done yet, and will likely be the last thing I do for the router table.  If I don’t get them done before the final post on the router table, I will post a picture of them in a future general update post.  Otherwise, from the front the router table looks complete visually.  However, there is still a bit more to go on the build, which I will go over in the next post.